ANALISA PENGARUH KEMIRINGAN SUDUT SCREW EXTRUDER TERHADAP KEAKURATAN DIAMETER FILAMENT 3D PRINTER BERBAHAN RECYCLED ABS, RECYCLE HDPE DAN POLYPROPYLENE
DOI:
https://doi.org/10.5281/zenodo.7684182Keywords:
Filament, Extrusion, Pulling Speed, Extrusion Temeperature, Filament DiameterAbstract
New extruder with recydled HDPE material (oil bottle), ABS, Polypropylene. High quality filaments are characterized by high durability and constant diameter. In this study, we used material variables dan helix angles. Accumulation of plastic waste is a major problem in many countries, including Indonesia. On the other hand, there is also a rapidly growing technology, namely 3D printing. With the development of plastic based 3D Printing, it has become very important to make 3D printing innovations more environmentally friendly. This can be achieved by using 3D printing filaments made from recycled plastic. This research is envolving. Combining 0o , 15o, and 25o extrusion screwing with HDPE, ABS, and polypropylene materials, the average diameter is close to 1.75mm to 1.76mm. Because = 0.519553 > 0.05 (2;4) = 6,9443. However after receiving the optimization parameters, the final result shows a defect in filament quality. Make the surface rough and easy to bend. Therefore, it is not possible to create object on a 3D printer using filaments made of polypropylene and recycled ABS and HDPE plastic.
Downloads
References
Angatkina, K.: Recycling of HDPE from MSW waste to 3D printing filaments. (2018) Badan pengawas obat dan makanan (BPOM). 2016. Plastik sebagai kemasan pangan. Diakses dari BADAN POM pada 20 Maret 2021. http:/ik.pom.go.id/v2015/artikel/Plastiksebagaikemasanpangan.pdf.
D. Seprianto, R. Wilza, dan Iskandar. 2017. Optimasi Parameter Pada Proses Pembuatan Objek 3D Printing Dengan Teknologi FDM Terhadap Akurasi Geometri. Seminar Nasional Teknik Industri Universitas Gadjah Mada 2017. ISBN 978-602-73461-6-1
R.A.Tya, Y. Setyoadi, dan A.Burhanudin.2020. Rancang Bangun Mesin Filament Extruder yang berbasis Arduino Mega2560 dengan hasil Acrylonitrile Butadiene Styrene (ABS). Science And Engineering National Seminar 5 (SENS 5). 17 Desember 2020. Semarang, Indonesia.
Suryana. Tatang. 2019. “Desain Modifikasi Screw Extruder Untuk Meningkatkan Outflow Yang Optimal Dan Meninimalkan Cacat Produk Pada Plastikâ€. Jurnal Ilmiah Teknobiz Magister Teknik Mesin Universitas Pancasila. Vol. 9 No. 1.
Vasile C dan Pascal M. 2005. Practical guide to polyethylene. Rapra Technology Limited.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Authors and Publisher
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to MACHINERY: Jurnal Teknologi Terapan as publisher of the journal. Copyright encompasses rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms, and any other similar reproductions, as well as translations.Â
MACHINERY: Jurnal Teknologi Terapan and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in MACHINERY: Jurnal Teknologi Terapan are the sole responsibility of their respective authors and advertisers.
