STUDI PEMANFAATAN LIMBAH ABU TERBANG BATUBARA (FLY ASH) DAN ALUMINIUM DAUR ULANG SEBAGAI PENGGANTI MATERIAL BANTALAN LUNCUR
DOI:
https://doi.org/10.5281/zenodo.4540856Keywords:
Aluminum Beverage Cans, Fly Ash, Casting, Glide Bearings, Melting Temperature 700°C, Hardness Test and Impact Test.Abstract
Aluminium is a soft metal with an attractive appearance, light weight and corrosion resistance. In this study, canned aluminium waste as a matrix and fly ash waste as reinforcement. In making specimens through a casting process using the casting method with a temperature of 7000C. The results of this study, the highest hardness value in the variation of alloy AL 60%: FA 40% at 82,726 kg/mm2 with the lowest hardness level at variation AL 100%: 0% FA at 60,036 kg/mm2 and the highest impact value on AL 100% : FA 0% at 0.0167 J/mm2 with the lowest impact value on the variation AL 60%: FA 40% at 0.0113 J/mm2. From these results it is known that the more weight fraction of fly ash is added to the aluminum, the level of hardness increases and this result is inversely proportional to the impact value because the higher the hardness value of a material, the more brittle the material is. So it can be concluded that canned aluminum waste material and coal fly ash are suitable to be used as a substitute for the sliding bearing material.
Downloads
References
Bashar, M.F. 2013. Desain dan Manufaktur Robot Rehabilitasi Anggota Gerak Bawah untuk Pasien Pasca Stroke. Tugas Akhir, Jurusan Teknik Mesin dan Industri, Universitas Gadjah Mada, Yogyakarta.
Dari, Tanty Wulan., Krisnawati. 2015. Hubungan Program Fisioterapi Dengan Tingkat Kemandirian Pada Pasien Post Stroke. Jurnal Keperawatan. Vol. VIII 1 Agustus 2015 ISSN 1979 – 8091.
Ginting, M., Sani, A. A., Astra, D. 2019. PENGARUH PARAMETER PROSES RAPID PROTOTYPING DENGAN TEKNOLOGI STEREOLITHOGRAPHY TERHADAP KEKERASAN SPESIMEN UJI. 11(2). ISSN : 2085-1286 E-ISSN : 2622-7649.
Harsono. 1996. Buku Ajar Neurologi Klinis. Penerbit Gadjah Mada Press. Yogyakarta.
Harsono. 1996. Kapita Selekta neurologi. Gadjah Mada University Press. Yogyakarta.
Hoeman, P. 1996. Rehabilitation Nursing: Process and Application. Second Edition. Mosby Year Book, Inc, St. Louis, USA.
Karabulut, S. 2016. Study on Machining Parameters for Thrust Force and Torque in Milling AA7039 Composites Reinforced with Al2O3/B4C/SiC Particles. International Journal of Engineering Technologies, IJET, 2(2), 68. https://doi.org/10.19072/ijet.05966.
Liu, Y., Liang, X., Saeed, A., Lan, W., & Qin, W. 2019. Properties of 3D printed dough and optimization of printing parameters. Innovative Food Science and Emerging Technologies, 54(March), 9–18. https://doi.org/10.1016/j.ifset.2019.03.008.
Mansjoer, A, dkk. 2000. Kapita Selekta Kedokteran. Edisi 3. Jilid 2. Penerbit Media Aesculapius Fakultas Kedokteran Universitas Indonesia. Jakarta.
Muharom, M., & Siswadi, S. 2015. Desain Eksperimen Taguchi Untuk Meningkatkan Kualitas Batu Bata Berbahan Baku Tanah Liat. Journal of Engineering and Management Industial System, 3(1), 43–46. https://doi.org/10.21776/ub.jemis.2015.003.01.7.
Nugraha, P. F. 2010. Pengembangan desain CPM (Continuous Passive Motion) elbow sebagai alat orthose aktif bagi pasien pasca operasi tulang siku tangan menggunakan kendali Microcontroller AT 89C51. Diakses dari https://eprints.uns.ac.id/153/.
O’Driscoll, S. W., Giori, N. J. 2000. Continuous Passive Motion (CPM): Theory and Principles of Clincial Application. Journal of Rehabilitation Research and Development, 37(2).
Saputra, A. W., Wardana, P. S., Rokhana, R. 2010. Robot Lengan 3 DOF dengan input sinyal EMG. Final Project. EEPIS.
Satyanarayana, B. and Prakash, Kode Jaya., 2015. Component Replication using 3D Printing Technology. Procedia Materials Science 10., p.263 – 269.
Wang, M. W., Arifin, F., & Kuo, H. L. 2020. Study on micromoulding of a high viewing angle LED lens. Plastics, Rubber and Composites, 49(1), 35–45. https://doi.org/10.1080/14658011.2019.1685803.
Wang, M. W., Arifin, F., Kuo, J. W., & Dzwo, T. H. 2020. Optimal Design of Plasticizing Screw Using Artificial Intelligent Approach. Journal of Physics: Conference Series, 1500(1). https://doi.org/10.1088/1742-6596/1500/1/012022.
Wang, M. W., Arifin, F., & Huang, J. 2019. Optimization Of The Micro Molding Of A Biconcave Structure. International Journal of Technology 10(2): 269-279
Wulandari, A., Wuryandari, T., & Ispriyanti, D. 2016. Penerapan Metode Taguchi Untuk Kasus Multirespon Menggunakan Pendekatan Grey Relational Analysis Dan Principal Component Analysis (Studi Kasus Proses Freis Komposit Gfrp). None, 5(4), 791–800.
Downloads
Published
How to Cite
Issue
Section
License
The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to MACHINERY: Jurnal Teknologi Terapan as publisher of the journal. Copyright encompasses rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms, and any other similar reproductions, as well as translations.Â
MACHINERY: Jurnal Teknologi Terapan and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in MACHINERY: Jurnal Teknologi Terapan are the sole responsibility of their respective authors and advertisers.
