ANALISIS PENGARUH PENAMBAHAN UNSUR MAGNESIUM TERHADAP KUAT LENGKUNG PADA MATERIAL ALUMINIUM

Article Sidebar

PDF (Bahasa Indonesia)
Published: Feb 28, 2023
DOI: https://doi.org/10.5281/zenodo.7684050
Keywords:
Aluminium, Magnesium, Sand Casting, Handle rem, Bending test

Main Article Content

farhan ikbar farhan
Mahasiswa Prodi Sarjana Terapan Teknik Mesin Produksi dan Perawatan, Politeknik Negeri Sriwijaya
Muhammad Rasid
Politeknik Negeri Sriwijaya
Ella Sundari
Politeknik Negeri Sriwijaya

Abstract

The brake handle is one of the components to restrain the vehicle's movement rate by holding the clamp mechanism, the problem that exists in the brake handle when there is a hard impact. Handles are usually made with aluminum metal material, so that aluminum has certain properties in this study combined with magnesium elements with variations of 1%, 3%, and 5%. Magnesium is the lightest chemical element among other industrial metals. The low density value and strength of magnesium is an advantage of this element as an alloy. The alloy used is a metal casting process using the sand casting method. After combining aluminum and magnesium in a bending test to get an acceptable bending strength. The percentage value of magnesium has a significant effect with a comparison of Fcount > Ftable value 72.29 > f0.0001(2;9) = 4.26. The percentage factor obtained is 87% and the maximum value is 38.08 kg/mm2 and the minimum value is 30.46 kg/mm2.

Downloads

Download data is not yet available.

Article Details

How to Cite
Ikbar, farhan ., Rasid, M., & Sundari, E. (2023). ANALISIS PENGARUH PENAMBAHAN UNSUR MAGNESIUM TERHADAP KUAT LENGKUNG PADA MATERIAL ALUMINIUM . MACHINERY: Jurnal Teknologi Terapan, 4(1), 1–9. https://doi.org/10.5281/zenodo.7684050
Issue
Vol. 4 No. 1 (2023): Machinery:04012023
Section
Articles
Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to MACHINERY: Jurnal Teknologi Terapan as publisher of the journal. Copyright encompasses rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms, and any other similar reproductions, as well as translations. 

MACHINERY: Jurnal Teknologi Terapan and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in MACHINERY: Jurnal Teknologi Terapan are the sole responsibility of their respective authors and advertisers.

References

Callister, Wd. 2007. Materials Science and Engineering Materials Science and Engineering : An Introduction, Jr.—7th Ed. p. Cm.,TA403.C23 2007, John Wiley & Sons.

Cholis, Setiawan Noor, Suharno, and Yadiono. 2013. “Pengaruh Penambahan Unsur Magnesium (Mg) Terhadap Kekerasan Dan Struktur Mikro Pada Pengecoran Aluminium.” Jurnal Ilmiah Pendidikan Teknik Mesin.

Cotton, F.A dan Wilkinson, G. (1989). Kimia Anorganik Dasar. Jakarta: UI Press.

Philip J. Ross. 1989. “Taguchi Techiques For Quality Engineering”. International Edition, McGraw Hill Book Co, New York

Setia, Irawan, Harjanto B, dan Subagsono. (2016). Analisis Pengaruh Penambahan Unsur Magnesium (Mg) 2% dan 5% terhadap Ketangguhan Impak, Tingkat Kekerasan dan Struktur Mikro pada Velg Aluminium (Al-5,68Si). Nosel 4(3), 1-7.

Sudjana. 1994. “Desain Dan Analisis Eksperimen”. Edisi III, Tarsito. Bandung.

Surdia, Tata, Shinroku S. (1999). Pengetahuan Bahan Teknik. Jakarta: PT. Pradnya Paramita.

Malik Yulianti. 2017. Teknik Pengecoran. Politeknik Industri Logam Morowali, Sulawesi Tengah.

Most read articles by the same author(s)