PERANCANGAN DAN PENGUJIAN ALAT PENGASIN TELUR BEBEK DENGAN AIR COMPRESSION PRESSURE
Keywords:
Proses Pengasinan, Telor asin, Tekanan udara 4-6 BarAbstract
The traditional method of making salted eggs usually using the salting, which is done well, its needs time about 14 days. This condition indicated to have a method that can speed up the process of salting the eggs. The process of salting eggs normally uses the usual soaking method where the eggs are coated with bricks and rubbing ash then left to stand. The diffusion of salt penetration in traditional salting takes place slowly. For this reason, the speed of salt penetration can be done by increasing the salt level in the soaking solution so that the penetration of salt into the eggs can take place faster. This methodology in this research study using of air pressure to speed up the process of salting the eggs. The method used is to use air pressure with the use of compressor air pressure at a pressure of 4 - 6 Bar with a salting test time of about 4 to 7 hours
Downloads
References
Coordinating Ministry For Economic, R.o.I., Master Plan for Acceleration and Expansion of Indonesia Economic Development (MP3EI) 2011–2025, Coordinating Ministry for Economic Affairs, Republic of Indonesia, Jakarta.
I. Ramli dan N. Wahab. 2020. Teknologi Pembuatan Telor Asin dengan Penerapan Metode Tekanan Osmotik. Iltek. Jurnal Teknologi. Vol. 15, hal. 82-86.
J. Zhang, J. Tan, W. tang, F. Wang, X. Zhao. 2019. Collapse performance of externally pressurized resin egg-shaped shell with corrosion thinning. International Journal of Pressure Vessel and Piping. Vol. 177, 103993.
M. H. Pulungan, S. Pandunusawan, A. Lastriyanto. 2019. Rancang bangun alat Pengasin Telor Puyuh (Coturnix coturnix) Berbasis Dehidrasi Osmosis Bertekanan Statis. Industria: Jurnal Teknologi dan Manajemen Agroindustri. Vol. 8, hal, 19-26.
M. Pekik, R. Ayu. 2018. Perancangan Tangki Stainless Steel untuk Penyimpanan Minyak Kelapa Murni Kapasitas 75 m^3. JTERA - Jurnal Teknologi Rekayasa, Vol. 3 (No. 1), Hal. 39-46.
P. Dony, M. Elfida, A. Yunus. 2018. Penentuan Laju Korosi dan Sisa Umur Pakai (Remaining Service Life/Rsl) pada Jalur Pipa Transportasi Crude Oil dari Spu-A Mundu ke Terminal Balongan di PT Pertamina Eksplorasi dan Produksi Asset 3 Jatibarang, Kabupaten Indramayu Provinsi Jawa Barat. Prosiding Teknik Pertambangan.
Romli, Analisis Sifat Mekanis Pengaruh Proses Pengelasa baja Tahan Karat, Jurnal Austenit. Vol 3, hal 21-34.
Rukmiasih, N. Ulupi, dan W. Indriani. 2015. Sifat Fisik, Kimia dan Organoleptik Telor Asin Melalui Penggaraman dengan Tekanan dan Konsentrasi Garam yang Berbeda. Jurnal Ilmu Produksi dan Teknologi Hasil Peternakan. Vol. 03, hal. 142-145.
Sujinem. 2006. Percepatan penetrasi garam ke dalam telur itik (Anasplatyrhincos) dengan metode tekanan dalam proses pembuatan telur asin. Institut Pertanian Bogor, Program Studi Teknologi Hasil Ternak. Fakultas Peternakan.
SNI,Standar Nasional Indonesia. 2012. Spesifikasi baut baja hasil perlakuan panas dengan kuat tarik minimum 830 Mpa (ASTM A325 M -04,IDT). In SNI ASTM A324:2012. BSN Badan Standardisasi Nasional.
Wulandari Z, Rukmiasih, T Suryati, C Budiman, N Ulupi. 2014. Teknik pengolahan Telur dan daging Unggas. IPB Press. Bogor.
X. Wang, Y. Huang, B. Zhou, W. Xu, X. Xiang, Q. Huang, dan S. Li. 2021. Improvement of quality and flavor of salted egg yolks by ultrasonic assisted cooking. Ultrasonic Sonochemistry. Vol. 75, 105579.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Authors and Publisher
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
The Authors submitting a manuscript do so on the understanding that if accepted for publication, Authors retain copyright and grant the AUSTENIT right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
AUSTENIT, the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in AUSTENIT are the sole responsibility of their respective authors and advertisers.
