DETERMINATION OF COOLANT OPTIMUM OPERATING TEMPERATURE IN INJECTION PRINTING PROCESS BASED ON PRODUCT PRECISION LEVEL

Authors

  • Olivia Laras Sati Universitas TamanSiswa Palembang
  • Ambo Intang Universitas TamanSiswa Palembang
  • Dendi Dwi Saputra Universitas TamanSiswa Palembang

DOI:

https://doi.org/10.53893/austenit.v14i2.4976

Keywords:

Injection Molding, Pet Gallon, Shrinkage

Abstract

Currently, plastic is more dominantly used because it is cheap, elastic and easy to process. To maintain the quality of plastic products, especially the type of Polyethylene Terephthalate (PET), the researchers implemented a modern plastic manufacturing system, namely using an injection molding system. In order to be able to meet the demands in solving problems that may arise in the process of making plastic products such as: quality, manufacturing time, and safety systems. The injection molding method replaces the old method, namely the hand press machine. This selection is based on advantages such as the consistency of the product produced because it is programmed, equipped with a control system, shorter product time, adequate security system, and other advantages. In this research, an experiment will be conducted to determine the optimum cooling temperature in the form of Pet Gallon. The problems that often occur are product defects due to shrinkage. In connection with this, the test results are obtained as follows: there is a difference in the shrinkage of product dimensions in the experiment using Cooled Chiller and Tower Chiller cooling, cooling has the greatest influence on the processing time of product manufacture, the optimum cooling temperature occurs at a cooling temperature of 200C.

Downloads

Download data is not yet available.

References

Amri, Alfan. (2009). Pengaruh Pendinginan dalam Proses Injection Molding Pembuatan Acetabular Cup pada Sambungan Hip. Universitas Muhammadiyah Surakarta. http://eprints.ums.ac.id/id/eprint/5947.

Asiah, D. (2020). Prinsip Dasar Penyimpanan Pangan Pada Suhu Rendah.

Budiarto. (2002). Perancangan Peralatan Pencetak.

Budiyono, S. (2012). Revitalisasi sistem pendingin evaporator tipe cooling tower. 837–846. https://digilib.batan.go.id/ppin/katalog/file/80-Budiyono,_Revitalisasi_Cooling_Tower_rev-yax(837-846).pdf.

Cahyadi, D. (2014). Analisis Parameter Operasi pada Proses Plastik Injection Molding untuk Pengendalian Cacat Produk. Fakultas Teknik, Universitas Serang Raya. Jakarta. https://jurnal.umj.ac.id/index.php/sintek/article/view/161/143.

Devalia, P. T., & Arief, T. M. (2019). Analisis dan Optimasi Parameter Proses Injeksi Plastik Multi Cavity untuk Meminimalkan Cacat Short Mold. POLBAN. https://doi.org/10.35313/irwns.v10i1.1465

Guerrier, P., Tosello, G., & Hattel, J. H. (2015). Analysis of cavity prebure and warpage of polyoxymethylene thin walled injection molded parts: Experiments and simulations. AIP Conference Proceedings, 1664(May 2015), 1–6. https://doi.org/10.1063/1.4918481.

Han, J.H. and Kim, Y. C. (2017). Study on Effect of Mold Temperature on the Injection Molded Article. Arch. Metall. Mater., Vol. 62.No, 1271–1274. DOI: 10.1515/amm-2017-0191.

HIDAYATI, B., Irawan, F., & Biola, Y. (2021). ANALISIS KELEMBABAN UDARA PADA AC SPLIT WALL USIA PAKAI 8 TAHUN DENGAN KAPASITAS 18000 Btu/hr. AUSTENIT, 13(1), 8–12. https://doi.org/10.5281/zenodo.4735758.

Kwon K., I. A. . I. , K. K. H. (2006). Theoritical and Experiment Studies of Anisotropic Shrinkage in Injection Molding of Various Polyester, Journal of Applied Polymer Science, Vol.102, pp.3526-3544. https://onlinelibrary.wiley.com/doi/epdf/10.1002/pen.20546.

Permana, M. R. R. (2013). Pengaruh Suhu Dan Waktu Proses Solvent Debinding Berat Greenpart Pada Metal Injection Molding Serbuk Alumunium. http://repository.unej.ac.id/handle/123456789/98791.

Ramadhan, A. I., Diniardi, E., & Daroji, M. (2017). Analisa Penyusutan Produk Plastik di Proses Injection Molding Menggunakan Media Pendingin Cooling Tower dan Udara dengan Material Polypropylene. Jrst: Jurnal Riset Sains Dan Teknologi, 1(2), 65. https://doi.org/10.30595/jrst.v1i2.1577.

Santoso, S. Teguh. (2014). Proses Produksi dan Perawatan Mesin Injection Molding.

Yoewono, S.& Kaswadi, A. (2014). Perbandingan Sistem Pendingin Konvensional dan Konformal pada Proses Cetak Injeksi Plastik. Proceeding SNTMUT. Jakarta: Universitas Trisakti.

Zulianto, D., Waluyo, B., & Pramuko. (2015). Cacat Warpage Pada Produk Injetion Molding Berbahan Polyprophylene (PP). 3–19. http://eprints.ums.ac.id/id/eprint/41085.

Downloads

Published

2022-11-14

How to Cite

Sati, O. L., Intang, A., & Saputra, D. D. (2022). DETERMINATION OF COOLANT OPTIMUM OPERATING TEMPERATURE IN INJECTION PRINTING PROCESS BASED ON PRODUCT PRECISION LEVEL. AUSTENIT, 14(2), 124–131. https://doi.org/10.53893/austenit.v14i2.4976

Issue

Vol. 14 No. 2 (2022): AUSTENIT: October 2022

Section

Articles

License

Copyright (c) 2022 Authors and Publisher

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

The Authors submitting a manuscript do so on the understanding that if accepted for publication, Authors retain copyright and grant the AUSTENIT right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

AUSTENIT, the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in AUSTENIT are the sole responsibility of their respective authors and advertisers.