RANCANG BANGUN CETAKAN PEMANEN (PERMANENT MOLD) UNTUK PEMBUATAN PULLEY ALUMINIUM
Keywords:
sand casting, permanent mold, non-ferro, bentuk geometri.Abstract
Many efforts have been done to increase efficiencies and margin (without ignoring the quality) in casting industry. Most of the producer of non-ferrous pulleys in South Sumatra region are handled by small and medium scale industries using simple technology. Therefore the research is intended to improve the process of making pulleys as cast product by changing the mold of the process from green sand casting mold to permanent mold (steel mold). As the geometry of the pulley is not so complex and the permanent mold enable us to mass produce of the non-ferrous pulley casting at a certain time. This research is conducted by making the design of the mold and the produce the prototype of the permanent molding in such a way so that the molding can replace the green sand casting molding to produce the same product without decreasing the quality. Research results show that permanent mold could produce pulleys as cast product faster than using the green sand mold and in certain amount of the product can cut the production cost.Downloads
Download data is not yet available.
References
1. Amstead B.H, Philips F. Ostwald, Myron L. Begeman, 1979, “Manufacturing Processesâ€, 7th edition, John Willey & Son Inc,
New York.
2. HC. Kazanas, Glenn E. Baker, Thomas G. Gregor., 1992, “Basic Manufacturing Processâ€, McGraw-Hill, Westerville, Ohio.
3. Kenneth G. Budinski, Michael K.
Budinski, 1999, “Engineering Materialâ€, sixth edition, Prentice Hall International Inc., New Jersey.
4. Mikell P. Groover, (1996), “Fundamental of Modern Manufacturingâ€, Prentice-Hall, Inc., New Jersey.
5. Tata Surdia, Prof., Ir., Shinroku Saito, Prof., DR., 2000, “Pengetahuan Bahan Teknikâ€, Pradnya Paramita, Jakarta.
6. Ir. Tata Surdia M.S. Met E. “Teknik Pengecoran Logam“, PT. Pradnya Paramita, Jakarta 1982
7. Shingley, Joseph Edward, Larry D.
Mitchel dan Ir. Gandhi Harahap, M.Eng,1994, “Perencanaan Teknik Mesinâ€. Edisi ke Empat jilid 2. Jakarta, Erlangga.
New York.
2. HC. Kazanas, Glenn E. Baker, Thomas G. Gregor., 1992, “Basic Manufacturing Processâ€, McGraw-Hill, Westerville, Ohio.
3. Kenneth G. Budinski, Michael K.
Budinski, 1999, “Engineering Materialâ€, sixth edition, Prentice Hall International Inc., New Jersey.
4. Mikell P. Groover, (1996), “Fundamental of Modern Manufacturingâ€, Prentice-Hall, Inc., New Jersey.
5. Tata Surdia, Prof., Ir., Shinroku Saito, Prof., DR., 2000, “Pengetahuan Bahan Teknikâ€, Pradnya Paramita, Jakarta.
6. Ir. Tata Surdia M.S. Met E. “Teknik Pengecoran Logam“, PT. Pradnya Paramita, Jakarta 1982
7. Shingley, Joseph Edward, Larry D.
Mitchel dan Ir. Gandhi Harahap, M.Eng,1994, “Perencanaan Teknik Mesinâ€. Edisi ke Empat jilid 2. Jakarta, Erlangga.
Downloads
Published
2010-10-01
How to Cite
Firdaus, F. (2010). RANCANG BANGUN CETAKAN PEMANEN (PERMANENT MOLD) UNTUK PEMBUATAN PULLEY ALUMINIUM. AUSTENIT, 2(02). Retrieved from https://jurnal.polsri.ac.id/index.php/austenit/article/view/110
Issue
Section
Articles
License
The Authors submitting a manuscript do so on the understanding that if accepted for publication, Authors retain copyright and grant the AUSTENIT right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
AUSTENIT, the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in AUSTENIT are the sole responsibility of their respective authors and advertisers.
