PENGARUH FEED RATE DAN DEPTH OF CUT TERHADAP KEKASARAN PERMUKAAN BAJA AISI 1045 CNC MILLING

Authors

  • Dwi Indra Nugraha Mahasiswa Prodi Teknik Mesin Produksi dan Perawatan, Politeknik Negeri Sriwjaya
  • Ahmad Junaidi Politeknik Negeri Sriwijaya
  • Suparjo . Politeknik Negeri Sriwijaya

DOI:

https://doi.org/10.5281/zenodo.8085379

Keywords:

Feed Rate, Depth Of Cut, End Milling, Kekasaran Permukaan

Abstract

This research is to determine the quality of machining products by testing the surface roughness. The research objective was to determine the effect of Feed Rate and Depth of Cut on the surface finish milling process on the surface roughness level. The method used in this research is the experimental method. The independent variables in this study were variations of Feed Rate and Depth of Cut where the Feed Rate values ​​taken was 300 mm/minute, 500 mm/minute, 700 mm/minute. The Depth of Cut values ​​taken was 0.1 mm, 0.2 mm, 0.3 mm and 0.4 mm. Based on the results of the roughness test of the Feed Rate and Depth of Cut variations of 0.1 mm each showed an average roughness value of 1.3005 μm, 1.70275 μm, 1.011 μm and 1.635 μm, the roughness test of the Feed Rate variation on Depth of Cut 0.2 mm each shows an average roughness value of 2.063 μm, 2.59325 μm, 2.31775 μm, and 2.75625 μm, roughness testing of the Feed Rate variation at a Depth of Cut of 0.3 mm shows average roughness values ​​of 3.01075 μm, 3.0215 μm, 3.01525 μm, and 3.091 μm, roughness testing of Feed Rate variation at Depth of Cut 0.4 mm each shows an average roughness value of 2.562 μm, 2.804 μm, 3.183 μm and 3.693 μm. Based on the standardization of the roughness value symbol according to (ISO) the results of research that has been done show that the value of the roughness number is N7-N8 in the range of 1.6 μm-3.2 μm.

Downloads

Download data is not yet available.

References

A Rachmanta, I. 2015. Pengaruh Parameter Pemotongan Terhadap Kekasaran Permukaan Baja Karbon Rendah pada Proses Conventional Menggunakan Pahat End Mill. Jurnal Teknik Mesin.

Ahmad. 2015. Pengaruh Feed Rate dan Depth of Cut terhadap Surface Roughness pada Proses Milling denganBantuan 4 AXIS CNC Machine. Jurnal Teknik Mesin.

Galang Sandy Proyogo, Nuraini Lusi, Chairul Anam. 2021. Optimasi Kekasaran Permukaan Baja AISI H13 pada Proses Permesinan Elektro Kimia Skala Laboratorium dengan Metode Taguchi

Guilford J.P. and B. Fruchter. 1978. Fundamental Statistic in Psychology and Education

Hermawan Asep Wahyu, Sakti Arya Mahendra. 2015. Pengaruh Kecepatan Putaran Spindel Dan Kedalaman Pemakanan Terhadap Tingkat Kerataan Dan Kekasaran Permukaan Alumunium 6061 Pada Mesin Frais Headman, Jurnal, Universitas Negeri Surabaya, Surabaya.

Joseph E Shigley. 1986. Perencanaan Teknik Mesin, Edisi Ke-dua Jilid 1, Erlangga, Jakarta.

Moch Yunus, M. Ginting, Karmin. 2013 Pengaruh Cutter Speed, Feed Rate Dan Dept Of Cut Pad Proses Cnc Milling Terhadap Nilai Kekasaran Baja Aisi 1045 Berbasis Regresi Linear

Mudjijanto, Eko Sutarto, Sarip. 2019. Analisis Karakteristik Geram Dan Kekasaran Permukaan Pada Proses Bubut Kecepatan Rendah Terhadap Baja Karbon.

Prabowo Gesit. 2016. Analisa Pengaruh Sumbu X Proses Kalibrasi Pada Mesin CNC Router 3 Axis

Prayogo Handoko, B. Tulung. 2012. Studi Parameter Pemesinan Optimum Pada Operas CNC End Milling Finishing Bahan Alumunium

Rahmat Dwi Cahyo, Muhammad Subhan , Indah Riezky Pratiwi. 2021. Analisis Kekasaran Permukaan Baja Aisi 1045 Pada Proses Pemesinan Bubut Cnc Dengan Metode Taguchi

Sugiarto K Adi. 2019. Analisa Nilai Kekasaran Permukaan Alumunium 6061 Dari Hasil Variasi Material Pahat Pada Mesin Cncrouter 5 Axismach 3 Tipe 5570

Sunardi Sunardi, Slamet Wiyono, Dhimas Satria, Rina Lusiani, Erny Listijorini, Wira Pratama. 2020. Perilaku kekasaran permukaan baja AISI 1045 terhadap kekerasan dan laju korosi serta daya lekat permukaan hasil elektroplating

Sularso. 1983. Dasar Perancangan Dan pemilihan Elemen Mesin

Published

2023-06-27

How to Cite

Nugraha, D. I., Junaidi, A., & ., S. (2023). PENGARUH FEED RATE DAN DEPTH OF CUT TERHADAP KEKASARAN PERMUKAAN BAJA AISI 1045 CNC MILLING. MACHINERY Jurnal Teknologi Terapan, 4(2), 98–108. https://doi.org/10.5281/zenodo.8085379

Most read articles by the same author(s)

Similar Articles

<< < 1 2 3 > >> 

You may also start an advanced similarity search for this article.